General (More Advanced PSW7 Inverter Charger)
NeoPower NPC Series pure sine wave inverter & charger is a more advanced model and an alternative product of PSW7 series. Developed on the base of our old design PSW7 series, the NPC series inverter & charger has achieved significant improvements on battery charging, AC transfer and etc. By adopting DIP (dual in-line package) switch, the NPC series pure sine wave inverter & charger provides more smart options for users to customize the performance of the device.
Application (More Advanced PSW7 Inverter Charger)
The NPC series pure sine wave inverter and charger is widely used in where need transferring DC to AC, such as battery charging requirements, personal computers, telecommunications and wherever required in the commercial, telecoms, mining or industrial markets, Commercial Solar, recreational vehicles, mobile office, industrial wind, fleet & utility vehicles, camping & outdoors, and renewable energy fields.
Performance (More Advanced PSW7 Inverter Charger)
1. High overload ability of NPC series inverter & charger can reach up to 300% rated power (20 sec.).
2. NPC pure sine wave inverter & charger adopts low quiescent current, and power saver mode to reduce power consumption to 10W (3s sensing cycle)/3W(30s sensing cycle) *. It can extract max. power from various batteries with different protections, and low voltage trip can be selected (9.5V/10V or 10V/10.5V).
3. Uses PFC(power factor correction) for charger, which has less power consumption than conventional units.
4. It has 15s delay before transfer when AC resumes, and overload protection when our NPC series inverter & charger equips with generator.
5. 10ms typical transfer time between battery and AC, which guarantees power continuity of NPC series inverter & charger. Uses selectable input AC voltage (184-253V or 154-253V) for different kinds of loads.
6. Our NPC series inverter & charger allow start up and through power with depleted batteries. Its powerful charge rate can reach up to 90Amp**.
7. It can offer 3-Step intelligent battery charging, and equipped with 8 preset battery type selector for totally flat batteries.
8. LCD status display, battery/AC priority switch, USB communication port are available for our NPC series inverter & charger, it also has 17 alarms/warnings for easier operation and trouble-shooting, and ability to switch the unit on/off. In addition, select/deselect power saver mode can be used too.
Note:*For 1KW only. **For some certain models.
Technical Specification (More Advanced PSW7 Inverter Charger)
|
Model |
1000W |
1500W |
2000W |
3000W |
4000W |
5000W |
6000W |
|
Inverter Output |
Continuous Output Power |
1000W |
1500W |
2000W |
3000W |
4000W |
5000W |
6000W |
|
Surge Rating(20s) |
3000W |
4500W |
6000W |
9000W |
12000W |
15000W |
18000W |
|
Capable of Starting Electric Motor |
1HP |
1.5HP |
2HP |
3HP |
4HP |
5HP |
6HP |
|
Output Waveform |
Pure Sine wave/Same as input (Bypass mode) |
|
Nominal Efficiency |
>88%(Peak) |
|
Line Mode Efficiency |
>95% |
|
Power Factor |
0.9-1.0 |
|
Nominal Output Voltage RMS |
100-110-120Vac / 220-230-240Vac |
|
Output Voltage Regulation |
±10% RMS |
|
Output Frequency |
50/60Hz ± 0.3Hz |
|
Short Circuit Protection |
Yes, Current Limit Function (Fault after 1sec) |
|
Typical transfer Time |
10ms(Max) |
|
THD |
< 10% |
|
DC Input |
Nominal Input Voltage |
12.0Vdc |
|
( *2 for 24Vdc, *4 for 48Vdc) |
|
Minimum Start Voltage |
10.0Vdc |
|
Low Battery Alarm |
10.5Vdc / 11.0Vdc |
|
Low Battery Trip |
10.0Vdc / 10.5Vdc |
|
High Voltage Alarm & Fault |
16.0Vdc |
|
High DC Input Recovery |
15.5Vdc |
|
Low Battery voltage recover |
13.0Vdc |
|
Idle Consumption-Search Mode |
< 25 W when Power Saver On |
|
Charge |
Input Voltage Range |
Wide: 90~135VAC / 164~243VAC;
Narrow: 100~135VAC / 194~243VAC; |
|
Output Voltage |
Depends on battery type |
|
Charger Breaker Rating |
10A |
10A |
10A |
20A |
20A |
30A |
30A |
|
Max Charge Rate |
35A / 70-90A Max (Charger Current Control) |
|
Over Charge Protection Shutdown |
15.7V for 12Vdc ( *2 for 24Vdc, *4 for 48Vdc) |
|
Charger curve(4 stage constant current) 4 step digital controlled progressive charge |
Battery types ( *2 for 24Vdc, *4 for 48Vdc) |
|
Battery type |
Fast Vdc |
Float Vdc |
|
Gel U.S.A |
14.0 |
13.7 |
|
A.G.M 1 |
14.1 |
13.4 |
|
A.G.M 2 |
14.6 |
13.7 |
|
Sealed Lead Acid |
14.4 |
13.6 |
|
Gel Euro |
14.4 |
13.8 |
|
Open Lead Acid |
14.8 |
13.3 |
|
Calcium |
15.1 |
13.6 |
|
De-sulphation |
15.5 for 4hrs |
|
Remote Control |
Yes. Optional |
|
Bypass & Protection |
Input Voltage Waveform |
Sine wave (Grid or Generator) |
|
Nominal Voltage |
120Vac |
230Vac |
|
Low Voltage Trip |
80V/90V±4% |
184V/154V±4% |
|
Low Voltage re engage |
90V/100V±4% |
194V/164V±4% |
|
High Voltage Trip |
140V±4% |
253V±4% |
|
High Voltage re engage |
135V±4% |
243V±4% |
|
Max Input AC Voltage |
150VAC |
270VAC |
|
Nominal Input Frequency |
50Hz or 60Hz (Auto detect) |
|
|
|
|
|
|
|
|
|
Low Frequency Trip |
47±0.3Hz for 50Hz, 57±0.3Hz for 60Hz |
|
Low Frequency re-engage |
48±0.3Hz for 50Hz, 58±0.3Hz for 60Hz |
|
High Frequency Trip |
55±0.3Hz for 50Hz, 65±0.3Hz for 60Hz |
|
High Frequency re-engage |
54±0.3Hz for 50Hz, 64±0.3Hz for 60Hz |
|
Output Short circuit protection |
Circuit breaker |
|
Bypass breaker rating |
10A |
15A |
20A |
30A |
30A |
40A |
40A |
|
Transfer switch rating |
30amp |
40amp |
|
Max bypass current |
30amp |
40amp |
|
Physical Spec |
Mounting |
Wall mount |
|
Inverter Dimensions(L*W*H) |
382*218*179mm |
442*218*179mm |
598*218*179mm |
|
Inverter Weight |
16KG |
17KG |
20KG |
24KG |
35KG |
45KG |
45KG |
|
Shipping Dimensions(L*W*H) |
520*315*300mm |
580*315*300mm |
740*315*300mm |
|
Shipping Weight |
18KG |
19KG |
22KG |
26KG |
37KG |
47KG |
47KG |
|
Display |
Status LEDs / Status LEDs +LCD |
|
Standard Warranty |
1 Year | |
Facebook
Linkedin
Twitter
Youtube